Repair Guide · Antminer · Refurbished · Hashboard Repair · Buying Guide
What refurbished should actually mean when you buy a used Antminer
Most used Antminer listings use "refurbished" as a marketing word, not a process description. For a farm operator, the difference between a cleaned unit and a chip-level rebuild is the difference between a 6-month and a 3-year service life — and the listing won't tell you which you're getting.
- 3
- Hashboards per Antminer unit
- ~0.4–0.5 V
- Typical BM13xx/BM15xx/BM17xx core voltage range
- 4
- Repair tiers that matter when buying
"Refurbished" is the most abused word in the secondary ASIC market. On a used Antminer listing it can describe anything from a unit that was blown out with compressed air to one that had three failed ASICs replaced and every hashboard reflowed at chip level. Both get the same label. Only one of them is worth farm money.
This is a guide to what the word should mean, how to tell the tiers apart from a listing and a test log, and what data to demand before you wire a pallet of S19s into a container.
The four tiers hiding behind one word
In practice, used Antminers sold as "refurbished" fall into four buckets. They are not equivalent, and the price gap between them is usually smaller than the reliability gap.
Cosmetic
Dust-out, fan swap, firmware reflash, case wipe
Nothing electrical
Failed ASICs, drifted buck stages, cracked joints
Preventive
Cosmetic plus thermal paste/pad replacement, PSU inspection
Thermal margin, worn fans
Any existing chip-level fault
Board-level swap
Failed hashboard replaced with a tested spare
The specific dead board
Age of the remaining boards, PSU wear
Chip-level rebuild
Per-ASIC test, failed chips replaced, buck stage and sense resistors verified, full burn-in
Chip-level faults, voltage-domain faults
Nothing - this is the real refurb
If a seller can't tell you which tier a unit went through, assume the first one. That is not cynicism; it is the base rate.
Why chip-level is the only tier that earns the name
An Antminer hashboard is a chain of ASICs (BM1397, BM1398, BM1366, BM1368, BM1370, BM1485, BM1489, BM1746 and so on, depending on model) fed by a multi-phase buck converter and a string of voltage-domain sense and feedback components. A board can pass a 10-minute pool test and still be sick.
The 10-minute test lie
A hashboard with one marginal ASIC will often hash at full rate in a cool room for ten minutes. It fails when ambient climbs, when the chip's junction temperature crosses its limit, or when the buck stage droops under sustained load. Cosmetic refurbishment never surfaces this. Chip-level testing does.What a genuine chip-level refurbishment involves, at minimum:
Step 1
Per-ASIC functional test
Every chip on the chain is tested individually for hashrate contribution, error rate and core voltage response — not just the board as a whole.
Step 2
Failed chip replacement
Dead or marginal ASICs are reballed and replaced, then the chain is retested end to end. Chip count and layout must match the board revision.
Step 3
Voltage-domain verification
Buck converter output, ripple and per-domain feedback are measured against the board spec. Drifted feedback resistors are a common silent killer.
Step 4
Thermal interface renewal
Paste or pads are replaced to spec — not smeared — and heatsink contact pressure is checked.
Step 5
Extended burn-in
The board runs at rated load for hours at elevated ambient, not minutes at room temperature, before it is cleared.
Anything short of that is maintenance, not refurbishment.
The verification data a real refurbisher already has
The useful question is not "is it refurbished?" but "show me the data." A seller who actually rebuilt the board will have it on file, because the rebuild process generates it. Ask for:
- Per-board chip logs from the miner's own kernel output, showing every chip reporting and no
xxxxor missing-chip entries - The test-bench ambient temperature and the PSU model used during burn-in
- Board serial numbers and photos showing chip layout and rework marks
- Firmware version and whether the unit was tested on stock or custom firmware
Reading a listing for the tells
Most listings leak which tier they are. Watch for these signals.
"Fully refurbished, tested"
Cosmetic or preventive
"Chip-level test log per board, please"
"All boards hashing at full rate"
Short pool test
"Burn-in duration and ambient temp?"
"New fans and paste"
Preventive only
"Any ASICs replaced? Which positions?"
"PSU included, tested"
Unknown PSU age
"PSU model, hours, cap inspection done?"
No test data offered
Cosmetic
Walk away or price it as untested
A listing that names the ASIC model, the board revision, the burn-in conditions and the failure rate of the batch is a different class of seller from one that says "100% working, fast ship."
What refurbishment does not cover
Even a genuine chip-level rebuild does not make a used Antminer new. Be clear-eyed about the residual wear:
PSU capacitors
Electrolytics age regardless of board condition. A rebuilt hashboard behind a tired PSU will still drop under load.
Connector and harness wear
Board-to-control-board harnesses and power connectors fatigue. Reworked boards with original harnesses carry that risk forward.
Control board and firmware
A refurbished hashboard on an old control board with stale firmware is a support ticket waiting to happen.
Mechanical wear
Fan bearings, heatsink screws and chassis threads degrade. None of it shows in a hash test.
Budget for board-level repair on any used fleet regardless of refurb tier. Refurbishment resets the clock on the items that were rebuilt; it does not stop the clock on the ones that weren't.
A practical buying checklist
Before you commit to a lot, run this sequence.
Step 1
Demand the chip log
Per board, from the miner itself. Missing-chip entries and xxxx placeholders are disqualifying.
Step 2
Confirm burn-in conditions
Hours at load, ambient temperature, PSU used. "Tested" without numbers is not a test.
Step 3
Ask which ASICs were replaced
Position and count. A seller who replaced chips knows exactly where.
Step 4
Inspect on arrival
Spot-check paste condition, rework marks, fan hours and PSU caps on a sample before the lot goes live.
Step 5
Run your own burn-in
Elevated ambient, rated load, several hours. Compare per-board hashrate against the seller's log.
If a unit passes all five, the word "refurbished" has earned its place on the invoice. If it fails at step one, you were never buying a refurbished miner — you were buying a cleaned one with a better story.
The bottom line
Refurbished should mean chip-level: every ASIC tested, failed chips replaced, voltage domains verified, thermal interface renewed, and a documented burn-in at elevated ambient. Anything less is maintenance. Price it that way, and demand the log that proves otherwise.Frequently asked questions
Is a cleaned and re-pasted Antminer the same as a refurbished one?
No. Cleaning and re-pasting is preventive maintenance. It does not restore a hashboard with a failed ASIC, a drifted buck converter, or a cracked solder joint — those are chip-level faults that survive a cosmetic refresh.
How do I verify a refurb claim before paying?
Ask for the per-board chip log from the miner's own kernel output, the test-bench ambient temperature and PSU used, and a photo of the board's serial and chip layout. A seller who rebuilt the board will have that data; a seller who wiped the dust off won't.
Does a refurbished Antminer still need on-site repair?
Yes, eventually. Refurbishment resets the clock on wear items — thermal interface, fans, PSU caps — but hashboards still fail at chip level under sustained load. Budget for board-level repair regardless of the refurb tier you buy.
Repair & maintenance
Get Your Miners Back to Full Hashrate
Chip-level diagnostics, component-level repair, and burn-in validation — on-site across the USA, no shipping required.